Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
Threads 41 to 60 of 94

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. Metal material 'R40P'

    Started by Manyquestions, 12-16-2013 09:14 PM
    r40p italian metal steel
    • Replies: 0
    • Views: 6,171
    Manyquestions
    12-16-2013, 09:14 PM Go to last post

  2. Document Management for Published Drawings

    Started by tstroh, 06-28-2022 10:13 AM
    • Replies: 1
    • Views: 6,152
    Kelly_Bramble
    06-28-2022, 10:59 AM Go to last post

  3. AN-40 Locknut Shaft Dimensions

    Started by bickeljm, 11-28-2012 11:00 AM
    • Replies: 1
    • Views: 6,118
    Kelly_Bramble
    11-28-2012, 04:42 PM Go to last post

  4. Engineers Edge Codes & Standards Forum Archive

    Started by administrator, 02-26-2011 05:27 PM
    • Replies: 0
    • Views: 6,105
    administrator
    02-26-2011, 05:27 PM Go to last post

  5. Confused Drawing projections - QUESTION

    Started by carlost, 07-04-2018 12:03 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 6,013
    carlost
    07-05-2018, 09:45 AM Go to last post

  6. Washer standards

    Started by Dominguez Mexico, 03-12-2012 01:50 PM
    • Replies: 2
    • Views: 5,990
    Dominguez Mexico
    05-30-2012, 11:18 AM Go to last post

  7. Stress Analysis of Chilled Water Under ground piping using Intergraph Caesar II

    Started by ppengg, 04-11-2016 01:40 PM
    chilled, hdpe, underground, water pipe
    • Replies: 1
    • Views: 5,858
    Cake of Doom
    04-12-2016, 02:48 AM Go to last post

  8. Vintage Military Aerospace Material Specifications

    Started by jeromy, 11-21-2016 08:29 AM
    aerospace, aviation, materials, specifications 1 Attachment(s)
    • Replies: 1
    • Views: 5,812
    Kelly_Bramble
    11-21-2016, 08:54 AM Go to last post

  9. EPM-001.12 Aerospace spec?

    Started by KELLY BURNS, 07-03-2012 01:34 PM
    • Replies: 2
    • Views: 5,773
    KELLY BURNS
    07-05-2012, 07:51 AM Go to last post

  10. Nozzle to cut plate

    Started by Dominguez Mexico, 08-17-2011 02:53 PM
    • Replies: 1
    • Views: 5,738
    PinkertonD
    08-17-2011, 06:22 PM Go to last post

  11. Self Tapping Screws Std. (18.6.4)

    Started by Francisco Michel, 11-05-2012 03:22 PM
    • Replies: 0
    • Views: 5,702
    Francisco Michel
    11-05-2012, 03:22 PM Go to last post

  12. Free standing canopy

    Started by Narcissa, 09-21-2011 01:45 PM
    canopy, drive-thru, free standing, open building
    • Replies: 0
    • Views: 5,643
    Narcissa
    09-21-2011, 01:45 PM Go to last post

  13. set SI-units

    Started by fdejong, 02-24-2021 01:05 AM
    si-system, unit
    • Replies: 1
    • Views: 5,595
    administrator
    02-24-2021, 07:24 AM Go to last post

  14. reduction of motor torque

    Started by axt, 08-05-2011 03:41 PM
    • Replies: 1
    • Views: 5,579
    jboggs
    08-09-2011, 06:26 AM Go to last post

  15. Astm b633

    Started by Dominguez Mexico, 03-21-2013 06:41 PM
    • Replies: 3
    • Views: 5,516
    PierArg
    03-27-2013, 08:00 AM Go to last post

  16. Three-Line Diagram?

    Started by Passacaglia, 07-21-2014 05:10 PM
    2 Attachment(s)
    • Replies: 3
    • Views: 5,439
    jackieann000
    12-31-2014, 10:32 PM Go to last post

  17. ASME Guided Study Classes

    Started by bryantsonnier, 06-12-2023 04:01 PM
    • Replies: 0
    • Views: 5,437
    bryantsonnier
    06-12-2023, 04:01 PM Go to last post

  18. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 04:33 AM
    • Replies: 1
    • Views: 5,422
    Kelly_Bramble
    05-22-2020, 07:27 AM Go to last post

  19. Standard face to face tolerances on welded components.

    Started by bryantsonnier, 05-27-2021 08:57 AM
    • Replies: 5
    • Views: 5,415
    Kelly_Bramble
    05-27-2021, 03:48 PM Go to last post

  20. Common Train Air/Rolling Resistance Values

    Started by Tmalott, 10-19-2016 09:42 PM
    common values, resistance, trains
    • Replies: 4
    • Views: 5,363
    Cake of Doom
    10-25-2016, 04:12 AM Go to last post
Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules