Page 1 of 5 1 2 3 ... LastLast
Threads 1 to 20 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. 10-Degree Modified Square Thread

    Started by rafazoide, 08-22-2012 03:23 PM
    • Replies: 0
    • Views: 6,675
    rafazoide
    08-22-2012, 03:23 PM Go to last post

  2. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 9,418
    gusschmoll
    09-27-2019, 01:08 PM Go to last post

  3. Allowable Stress Design and Plastic Design, June 1, 1989

    Started by Dominguez Mexico, 07-28-2011 11:34 AM
    • Replies: 4
    • Views: 12,888
    Dominguez Mexico
    08-01-2011, 03:04 PM Go to last post

  4. Aluminum specific weight

    Started by Dominguez Mexico, 06-14-2011 07:20 PM
    • Replies: 10
    • Views: 76,506
    CCR5600Design
    07-08-2011, 02:25 PM Go to last post

  5. AN-40 Locknut Shaft Dimensions

    Started by bickeljm, 11-28-2012 11:00 AM
    • Replies: 1
    • Views: 5,914
    Kelly_Bramble
    11-28-2012, 04:42 PM Go to last post

  6. ANSI/ASME Standards for Fasteners - Thread Length Inquiry

    Started by Chubbs, 09-06-2011 01:24 PM
    ansi, asme, fastener, length, standard 1 Attachment(s)
    • Replies: 1
    • Views: 10,922
    Kelly_Bramble
    09-06-2011, 02:37 PM Go to last post

  7. AS/NZS 1170.2: action combination factor (Kc)

    Started by sarahxaviera, 10-13-2017 12:53 PM
    2 Attachment(s)
    • Replies: 0
    • Views: 7,789
    sarahxaviera
    10-13-2017, 12:53 PM Go to last post

  8. ASCE7-05 Wind Load C&C

    Started by xezio, 06-20-2012 04:39 PM
    • Replies: 1
    • Views: 9,063
    Kelly_Bramble
    06-22-2012, 07:19 AM Go to last post

  9. ASME Code stamping(U Stamp)

    Started by tarafdar, 09-12-2011 01:07 PM
    • Replies: 0
    • Views: 6,190
    tarafdar
    09-12-2011, 01:07 PM Go to last post

  10. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 09:46 AM
    • Replies: 4
    • Views: 11,919
    petronextinternational
    02-14-2019, 03:38 AM Go to last post

  11. ASME Guided Study Classes

    Started by bryantsonnier, 06-12-2023 04:01 PM
    • Replies: 0
    • Views: 5,206
    bryantsonnier
    06-12-2023, 04:01 PM Go to last post

  12. ASME Section Viii (no stamp) vessel operates below 15 psig

    Started by crspublic8, 07-14-2018 11:57 AM
    • Replies: 1
    • Views: 8,057
    Kelly_Bramble
    07-15-2018, 09:12 AM Go to last post

  13. Astm b633

    Started by Dominguez Mexico, 03-21-2013 06:41 PM
    • Replies: 3
    • Views: 5,335
    PierArg
    03-27-2013, 08:00 AM Go to last post

  14. ASTM Yield and Ulitimate Clarification

    Started by RWOLFEJR, 03-16-2012 10:11 AM
    • Replies: 2
    • Views: 10,434
    Kelly_Bramble
    03-18-2012, 08:32 AM Go to last post

  15. Automated monitor and Control of agricultural greenhouse

    Started by Eugene Nsabimana, 04-16-2015 02:59 PM
    • Replies: 1
    • Views: 4,273
    jboggs
    04-17-2015, 03:04 PM Go to last post

  16. Bridge design specifications

    Started by Kelly_Bramble, 04-25-2014 08:22 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 4,890
    jackieann000
    12-04-2014, 02:15 AM Go to last post

  17. Bs 1571

    Started by plg6667, 03-30-2011 01:33 AM
    • Replies: 0
    • Views: 4,934
    plg6667
    03-30-2011, 01:33 AM Go to last post

  18. burrs on machined plastic gasket

    Started by dfike19380, 08-31-2011 10:58 AM
    • Replies: 4
    • Views: 7,669
    PinkertonD
    08-31-2011, 06:10 PM Go to last post

  19. Code standard for hole callout note formats

    Started by brad_winesett, 10-15-2020 10:49 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 8,067
    Kelly_Bramble
    10-15-2020, 03:13 PM Go to last post

  20. Common Train Air/Rolling Resistance Values

    Started by Tmalott, 10-19-2016 09:42 PM
    common values, resistance, trains
    • Replies: 4
    • Views: 4,858
    Cake of Doom
    10-25-2016, 04:12 AM Go to last post
Page 1 of 5 1 2 3 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules