Page 1 of 5 1 2 3 ... LastLast
Threads 1 to 20 of 86

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. set SI-units

    Started by fdejong, 02-24-2021 02:05 AM
    si-system, unit
    • Replies: 1
    • Views: 92
    administrator
    02-24-2021, 08:24 AM Go to last post

  2. Engineering Drawings Standard for Black and White or Color?

    Started by hogpaw, 12-10-2013 08:43 AM
    • Replies: 9
    • Views: 16,086
    Solidworksguy
    11-17-2020, 11:25 AM Go to last post

  3. Code standard for hole callout note formats

    Started by brad_winesett, 10-15-2020 11:49 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 861
    Kelly Bramble
    10-15-2020, 04:13 PM Go to last post

  4. Need Ventilation requirements and exepmtions

    Started by gilramirez716, 08-08-2020 06:45 PM
    cfm requirement, safety, ventilation requirements
    • Replies: 2
    • Views: 3,517
    gilramirez716
    08-09-2020, 04:04 PM Go to last post

  5. Temporary Works Test Rig Design Codes

    Started by luke_sheader, 07-09-2020 09:59 AM
    • Replies: 0
    • Views: 708
    luke_sheader
    07-09-2020, 09:59 AM Go to last post

  6. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 05:33 AM
    • Replies: 1
    • Views: 642
    Kelly Bramble
    05-22-2020, 08:27 AM Go to last post

  7. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 12:18 PM
    • Replies: 1
    • Views: 2,476
    gusschmoll
    09-27-2019, 02:08 PM Go to last post

  8. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 10:46 AM
    • Replies: 4
    • Views: 5,079
    petronextinternational
    02-14-2019, 04:38 AM Go to last post

  9. Driving vs. Driven Dimensions

    Started by kcampbe, 11-28-2016 04:42 PM
    • Replies: 5
    • Views: 9,122
    petronextinternational
    02-14-2019, 04:37 AM Go to last post

  10. Shraeder/Presta Cycle Tire Standards

    Started by richard_fox, 06-23-2018 03:30 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 1,924
    petronextinternational
    01-25-2019, 12:41 AM Go to last post

  11. ASME Section Viii (no stamp) vessel operates below 15 psig

    Started by crspublic8, 07-14-2018 12:57 PM
    • Replies: 1
    • Views: 1,957
    Kelly Bramble
    07-15-2018, 10:12 AM Go to last post

  12. Safety Standard for polymeric materials used in automotive electronics

    Started by andrew_templeton, 10-13-2016 03:59 PM
    • Replies: 1
    • Views: 1,473
    jamessmith00444
    07-13-2018, 08:17 AM Go to last post

  13. Confused Drawing projections - QUESTION

    Started by carlost, 07-04-2018 01:03 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 1,421
    carlost
    07-05-2018, 10:45 AM Go to last post

  14. AS/NZS 1170.2: action combination factor (Kc)

    Started by sarahxaviera, 10-13-2017 01:53 PM
    2 Attachment(s)
    • Replies: 0
    • Views: 3,086
    sarahxaviera
    10-13-2017, 01:53 PM Go to last post

  15. Vintage Military Aerospace Material Specifications

    Started by jeromy, 11-21-2016 09:29 AM
    aerospace, aviation, materials, specifications 1 Attachment(s)
    • Replies: 1
    • Views: 1,772
    Kelly Bramble
    11-21-2016, 09:54 AM Go to last post

  16. Common Train Air/Rolling Resistance Values

    Started by Tmalott, 10-19-2016 10:42 PM
    common values, resistance, trains
    • Replies: 4
    • Views: 1,609
    Cake of Doom
    10-25-2016, 05:12 AM Go to last post

  17. ISO to ANSI conversion

    Started by lydiaai, 08-09-2016 03:15 AM
    ansi, conversion, iso
    • Replies: 0
    • Views: 3,807
    lydiaai
    08-09-2016, 03:15 AM Go to last post

  18. material specification

    Started by mohit333, 04-15-2015 12:28 AM
    materials, standards, steel
    • Replies: 2
    • Views: 4,501
    akashram
    04-30-2016, 07:01 AM Go to last post

  19. Stress Analysis of Chilled Water Under ground piping using Intergraph Caesar II

    Started by ppengg, 04-11-2016 02:40 PM
    chilled, hdpe, underground, water pipe
    • Replies: 1
    • Views: 2,881
    Cake of Doom
    04-12-2016, 03:48 AM Go to last post

  20. HELP! Intergraph Caesar II UG HDPE pipe stress analysis

    Started by ppengg, 04-11-2016 02:46 PM
    caesar ii, intergraph, ug piping
    • Replies: 0
    • Views: 3,436
    ppengg
    04-11-2016, 02:46 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules