Page 5 of 9 FirstFirst ... 3 4 5 6 7 ... LastLast
Threads 81 to 100 of 161

Forum: Industrial Design & Engineering Forum

Industrial design, engineering and related forum discussion topics.

  1. Smile Forced Energy Generator

    Started by KennyFerdinand, 09-17-2015 05:17 PM
    2 Attachment(s)
    • Replies: 5
    • Views: 5,689
    Dan S.
    03-27-2016, 12:52 PM Go to last post

  2. Basic pneumatic press compressive strength question

    Started by khale, 06-06-2020 08:53 AM
    compressive stress, force, pneumatic cylinder press, stamping press, strength
    • Replies: 2
    • Views: 4,149
    khale
    06-07-2020, 04:03 PM Go to last post

  3. Suitable bearing for high speed oscillatory motion

    Started by kumarsukumar90, 09-15-2023 03:03 AM
    • Replies: 1
    • Views: 5,540
    joe_boggs
    09-15-2023, 01:57 PM Go to last post

  4. Cable Carrier Selection for SMAW on Track

    Started by kyle_love, 03-05-2020 10:30 AM
    4 Attachment(s)
    • Replies: 4
    • Views: 4,256
    kyle_love
    03-06-2020, 12:02 PM Go to last post

  5. no play peg in hole that locks but can be removed and replaced easily

    Started by lamby, 02-12-2012 12:28 PM
    • Replies: 2
    • Views: 4,104
    RWOLFEJR
    02-12-2012, 01:54 PM Go to last post

  6. Is there any specific Pressure gauge for air,water,gas or vapor Pressure ???

    Started by Leaxley, 06-08-2011 04:06 AM
    • Replies: 5
    • Views: 16,403
    Leaxley
    06-23-2011, 12:21 AM Go to last post

  7. Pressure Relief for High Pressure Separator Application

    Started by liecdre97, 07-08-2015 04:02 PM
    pressure, safety, valve
    • Replies: 1
    • Views: 4,659
    JAlberts
    07-09-2015, 04:18 PM Go to last post

  8. Engineering Senior Design Project Motor Calcuations

    Started by link_varnum, 09-13-2016 11:04 AM
    1 Attachment(s)
    • Replies: 1
    • Views: 2,887
    jboggs
    09-13-2016, 12:23 PM Go to last post

  9. Biocompatible Paint for medical product

    Started by lisa i4, 06-27-2011 05:47 AM
    • Replies: 1
    • Views: 9,776
    Marky
    06-27-2011, 08:57 AM Go to last post

  10. Impact (impulse) between two rotating (around fixed axis) bodies

    Started by lskrinjar, 08-10-2011 04:09 AM
    • Replies: 0
    • Views: 5,841
    lskrinjar
    08-10-2011, 04:09 AM Go to last post

  11. Confused Torsion in a shaft

    Started by LuG, 12-12-2012 03:41 AM
    2 Attachment(s)
    • Replies: 1
    • Views: 5,132
    Kelly_Bramble
    12-12-2012, 08:09 AM Go to last post

  12. Cool Hydraulic Design

    Started by magbrr, 03-03-2011 05:51 AM
    • Replies: 1
    • Views: 5,812
    Kelly_Bramble
    03-03-2011, 07:30 AM Go to last post

  13. Air Speed required for car drying

    Started by Marco Genicolo, 09-19-2011 11:52 AM
    air speed, car drying
    • Replies: 2
    • Views: 4,651
    PinkertonD
    09-20-2011, 12:46 PM Go to last post

  14. looking for a special valve

    Started by marokay, 10-11-2014 04:54 AM
    • Replies: 5
    • Views: 3,319
    Sheppie
    10-17-2014, 04:56 AM Go to last post

  15. Mad2 Chemical Tee Connections

    Started by Marshal, 07-12-2011 08:33 AM
    chemical tee, gasket
    • Replies: 2
    • Views: 5,903
    PinkertonD
    07-12-2011, 08:54 AM Go to last post

  16. Air temperature drop in an duct.

    Started by mattstandhaven, 06-28-2019 05:27 AM
    • Replies: 1
    • Views: 5,004
    Kelly_Bramble
    06-28-2019, 07:09 AM Go to last post

  17. Cleaning of conveyor belts

    Started by ma_ha, 11-20-2022 09:08 AM
    • Replies: 4
    • Views: 5,450
    ma_ha
    11-22-2022, 12:31 PM Go to last post

  18. Spray nozzles for large jet engine

    Started by Metiz, 04-15-2013 09:55 AM
    • Replies: 0
    • Views: 3,632
    Metiz
    04-15-2013, 09:55 AM Go to last post

  19. Plain Bearing for 2 Inch Pole Question

    Started by Michael Meio, 07-22-2015 01:00 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 4,068
    jboggs
    07-23-2015, 09:50 AM Go to last post

  20. Bang Head Trying to identify the French equivalent expression for cold rolling mill.

    Started by MikeSpencer, 08-30-2013 05:03 AM
    • Replies: 2
    • Views: 3,836
    Dominguez Mexico
    08-30-2013, 09:04 AM Go to last post
Page 5 of 9 FirstFirst ... 3 4 5 6 7 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules