Page 9 of 30 FirstFirst ... 7 8 9 10 11 19 ... LastLast
Threads 161 to 180 of 597

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. Could this clockwork compete other storage methods?

    Started by yahya_sharif, 09-28-2018 07:44 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 2,198
    yahya_sharif
    09-28-2018, 07:44 AM Go to last post

  2. Timing pulley type selection for power transmission

    Started by futterama, 09-28-2018 03:33 AM
    • Replies: 0
    • Views: 2,318
    futterama
    09-28-2018, 03:33 AM Go to last post

  3. Controlling low air pressure

    Started by mike_landeros, 09-22-2018 10:46 PM
    • Replies: 2
    • Views: 2,300
    Hudson
    09-23-2018, 09:31 AM Go to last post

  4. Question Deck Joist Bending Calculations

    Started by exp741, 09-18-2018 11:11 AM
    2 Attachment(s)
    • Replies: 3
    • Views: 2,252
    Hudson
    09-19-2018, 09:46 PM Go to last post

  5. new style submarine/ pressure hull design

    Started by eddiewelch83, 09-03-2018 09:16 AM
    • Replies: 2
    • Views: 2,164
    Kelly_Bramble
    09-04-2018, 07:28 AM Go to last post

  6. Question Sensitive accurate material extraction tool for clay like material w/ thin sheathing

    Started by kde5fan, 08-27-2018 12:19 PM
    • Replies: 1
    • Views: 2,375
    JAlberts
    08-30-2018, 04:19 PM Go to last post

  7. Question Unexpectedly high normal stress -beam bending.

    Started by robert_cibula, 08-24-2018 03:14 PM
    euler-bernoulli theory, normal stress 4 Attachment(s)
    • Replies: 0
    • Views: 2,354
    robert_cibula
    08-24-2018, 03:14 PM Go to last post

  8. High Push / Pull Force 12 Volt Actuator

    Started by jasonroliver, 08-20-2018 12:29 PM
    • Replies: 1
    • Views: 2,355
    Kelly_Bramble
    08-20-2018, 12:52 PM Go to last post

  9. Lightbulb Career after BSME

    Started by nachaat25, 08-19-2018 10:04 PM
    • Replies: 1
    • Views: 2,579
    jboggs
    08-20-2018, 07:02 AM Go to last post

  10. Pressure testable burst disc....

    Started by ezetom, 08-04-2018 05:16 PM
    • Replies: 1
    • Views: 3,085
    JAlberts
    08-15-2018, 04:53 PM Go to last post

  11. Calculating required diameter of rod to support a given load

    Started by schembriandrew123, 08-14-2018 08:39 AM
    • Replies: 5
    • Views: 7,966
    Kelly_Bramble
    08-15-2018, 08:50 AM Go to last post

  12. Pump Inducer nomenclature

    Started by miladasiaban, 08-14-2018 03:28 AM
    cavitation, inducer, pump, turbomachinary 2 Attachment(s)
    • Replies: 0
    • Views: 2,594
    miladasiaban
    08-14-2018, 03:28 AM Go to last post

  13. Forces on bolt during vibration

    Started by winghoe_tan, 07-30-2018 02:22 AM
    1 Attachment(s)
    • Replies: 2
    • Views: 2,874
    winghoe_tan
    07-30-2018, 07:36 PM Go to last post

  14. Confused Centrifugal compressor Inspection

    Started by max_zhura, 05-15-2018 06:05 AM
    • Replies: 1
    • Views: 2,829
    ricardo_santos188
    07-22-2018, 03:54 PM Go to last post

  15. Restoration screw thread issue - Old unidentified pistol late 1700

    Started by zoichi_kanoe, 07-18-2018 02:59 AM
    • Replies: 3
    • Views: 3,752
    Cake of Doom
    07-20-2018, 04:19 AM Go to last post

  16. Tandem One-Way-Bearings

    Started by nsoller, 07-11-2018 05:51 PM
    bearing, clutch, sprag
    • Replies: 4
    • Views: 3,054
    nsoller
    07-13-2018, 12:52 PM Go to last post

  17. Confused Some questions regarding pressure vessels

    Started by ernst_filmore, 06-22-2018 06:40 PM
    • Replies: 2
    • Views: 2,965
    JAlberts
    06-26-2018, 07:31 PM Go to last post

  18. Effect of change in rpm on gear design

    Started by mike_man, 06-20-2018 09:23 AM
    • Replies: 1
    • Views: 2,406
    jboggs
    06-20-2018, 11:54 AM Go to last post

  19. Two different capacity fans in parallel

    Started by akaul, 06-20-2018 01:03 AM
    • Replies: 0
    • Views: 2,569
    akaul
    06-20-2018, 01:03 AM Go to last post

  20. 2 stroke piston inertia formulas

    Started by 19jaguar75, 06-05-2018 03:58 PM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 20
    • Views: 7,640
    19jaguar75
    06-09-2018, 03:03 PM Go to last post
Page 9 of 30 FirstFirst ... 7 8 9 10 11 19 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules