Page 1 of 30 1 2 3 11 ... LastLast
Threads 1 to 20 of 597

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. Load capacity of rectangular steel tubing

    Started by r2dudes, 02-27-2015 09:03 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 80,809
    Kelly_Bramble
    05-21-2015, 07:32 AM Go to last post

  2. Square tube aluminum load ratings

    Started by cameron33, 04-15-2013 11:23 AM
    1 Attachment(s)
    • Replies: 5
    • Views: 70,579
    jboggs
    01-28-2015, 09:53 AM Go to last post

  3. Question What is the difference between a motor and pump??

    Started by vaishalshah, 01-01-2014 07:40 AM
    • Replies: 8
    • Views: 62,039
    JT101
    11-04-2015, 04:20 PM Go to last post

  4. IPS Versus NPT Pipe Thread Standards: What Is the Difference?

    Started by TomBrook11232, 01-15-2017 06:51 PM
    ips, nps, pipe threads
    • Replies: 2
    • Views: 44,441
    Cragyon
    01-16-2017, 10:20 PM Go to last post

  5. Calculate Max Permissible Torque in a Shaft

    Started by Glamdring, 11-28-2013 06:31 AM
    • Replies: 3
    • Views: 24,810
    Kelly_Bramble
    12-01-2013, 03:12 PM Go to last post

  6. Knurling Specification and Tool Size Chart

    Started by westfald, 05-01-2013 02:31 PM
    chart, definition, knurl, knurling
    • Replies: 5
    • Views: 15,630
    PinkertonD
    05-02-2013, 07:47 PM Go to last post

  7. Compression Force on square tube

    Started by oak123, 07-19-2016 02:35 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 13,156
    JAlberts
    07-26-2016, 05:38 PM Go to last post

  8. Turntable torque requirement

    Started by laengineer, 08-29-2013 10:09 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 13,073
    Cragyon
    11-03-2013, 03:36 PM Go to last post

  9. Ventilation System for Diesel Generator Set

    Started by hafiz88a, 12-18-2013 06:26 AM
    generator, ventilation 2 Attachment(s)
    • Replies: 6
    • Views: 13,055
    haseeb_Mech
    07-11-2016, 05:11 AM Go to last post

  10. Design of 4 stroke CI engine from few parameters(bmep,Brake Po,max.mean piston speed)

    Started by marellasunny, 05-05-2013 05:52 AM
    combustion engine, ice 1 Attachment(s)
    • Replies: 6
    • Views: 12,492
    marellasunny
    05-23-2013, 12:13 AM Go to last post

  11. Question Dimension Marking with Center Lines in Engineering Drawings

    Started by adirajck, 07-16-2019 03:24 AM
    4 Attachment(s)
    • Replies: 16
    • Views: 12,072
    Kelly_Bramble
    07-22-2019, 07:39 AM Go to last post

  12. Cylindrical Pressure Vessel with Stiffeners stress calculations

    Started by cr668288, 04-30-2013 07:17 AM
    • Replies: 13
    • Views: 11,535
    PinkertonD
    05-03-2013, 09:01 AM Go to last post

  13. Reasonable rotating shaft deflection?

    Started by Garth M, 07-23-2014 11:04 AM
    deflection, design, shaft 1 Attachment(s)
    • Replies: 5
    • Views: 11,225
    Riner
    07-25-2014, 09:20 AM Go to last post

  14. Square Steel Tubing Calculation (and related design questions)

    Started by daigoro1715, 07-04-2013 03:02 PM
    • Replies: 8
    • Views: 10,633
    RWOLFEJR
    07-07-2013, 09:53 AM Go to last post

  15. Mechanical engineering subdisciplines

    Started by hamidun, 08-25-2014 02:08 AM
    • Replies: 11
    • Views: 10,006
    akashram
    02-04-2016, 01:25 AM Go to last post

  16. UNI 6604 Key Material Specifications

    Started by MSUdawg711, 07-25-2013 07:56 AM
    • Replies: 4
    • Views: 9,540
    MSUdawg711
    07-25-2013, 10:42 AM Go to last post

  17. “Shape function for ellipsoidal pits” explanation

    Started by habibur0030, 03-26-2015 09:43 AM
    • Replies: 0
    • Views: 9,297
    habibur0030
    03-26-2015, 09:43 AM Go to last post

  18. why plastic for this piece?

    Started by 20GT, 03-24-2016 09:36 PM
    4 Attachment(s)
    • Replies: 3
    • Views: 9,034
    20GT
    03-25-2016, 09:53 PM Go to last post

  19. Troubleshooting Shaft Wear

    Started by surfmase, 09-24-2015 02:12 AM
    1 Attachment(s)
    • Replies: 8
    • Views: 8,755
    surfmase
    11-04-2015, 01:28 AM Go to last post

  20. how to calculate the steel weight?

    Started by machinemfg, 12-28-2018 08:50 PM
    • Replies: 8
    • Views: 8,659
    luzharrison1952
    01-11-2022, 04:10 AM Go to last post
Page 1 of 30 1 2 3 11 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules