Page 24 of 30 FirstFirst ... 14 22 23 24 25 26 ... LastLast
Threads 461 to 480 of 597

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. Torque required for pinch rollers

    Started by rawkstar320, 03-10-2014 06:56 AM
    1 Attachment(s)
    • Replies: 1
    • Views: 4,508
    Kelly_Bramble
    03-10-2014, 02:55 PM Go to last post

  2. Rack & Pinion versus Lead/ball Screw

    Started by rayvcdw, 06-03-2016 03:52 AM
    • Replies: 4
    • Views: 3,131
    rayvcdw
    06-03-2016, 05:54 PM Go to last post

  3. Co-efficient of Friction of elastomer seal

    Started by rc_shaha, 05-23-2015 02:58 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 3,002
    JAlberts
    05-23-2015, 05:28 PM Go to last post

  4. Diesel Engine Retrofit

    Started by Reaper, 04-28-2014 02:32 PM
    analysis, heat, radiator, retrofit, thermal
    • Replies: 3
    • Views: 3,724
    engineeringdesign
    05-02-2014, 12:35 AM Go to last post

  5. Typical jobs with a BS in mechanical engineering technology

    Started by redsoxreid, 05-09-2017 03:46 PM
    • Replies: 1
    • Views: 2,620
    jboggs
    05-09-2017, 08:45 PM Go to last post

  6. Question Heat transfer through convection & radiation

    Started by RekhaP88, 04-18-2016 08:46 PM
    conduction, convection, heat transfer, radiation, radiation heat transfer 1 Attachment(s)
    • Replies: 0
    • Views: 3,421
    RekhaP88
    04-18-2016, 08:46 PM Go to last post

  7. Driven-Pinion Spur Gears?

    Started by richard_smith, 07-05-2020 05:07 AM
    gears, pinion, wheel
    • Replies: 3
    • Views: 3,564
    Hudson
    07-07-2020, 10:27 AM Go to last post

  8. High pressure, high temperature, low cost tank

    Started by rich_m, 07-07-2019 03:06 PM
    • Replies: 1
    • Views: 3,154
    shiloh
    07-08-2019, 08:19 AM Go to last post

  9. Question Pneumatic Ram Lubrication

    Started by rickduley, 01-07-2024 11:59 PM
    lubrication, pneumatic
    • Replies: 0
    • Views: 1,212
    rickduley
    01-07-2024, 11:59 PM Go to last post

  10. Confused Mechanical products

    Started by Rina, 10-01-2015 11:24 AM
    • Replies: 1
    • Views: 2,586
    jboggs
    10-02-2015, 07:34 AM Go to last post

  11. Petrochemical Oil & Gas

    Started by Rizwan786, 12-07-2014 12:00 PM
    • Replies: 0
    • Views: 2,645
    Rizwan786
    12-07-2014, 12:00 PM Go to last post

  12. Holding a baseline pressure

    Started by rkreidler3, 07-14-2022 02:39 PM
    dc motor, pressure, pump, solenoid, suction 2 Attachment(s)
    • Replies: 4
    • Views: 2,052
    rkreidler3
    07-21-2022, 07:43 AM Go to last post

  13. How do i calculate the strength of a friction hinge?

    Started by RMAR, 05-25-2016 10:49 PM
    • Replies: 0
    • Views: 2,515
    RMAR
    05-25-2016, 10:49 PM Go to last post

  14. Question Unexpectedly high normal stress -beam bending.

    Started by robert_cibula, 08-24-2018 03:14 PM
    euler-bernoulli theory, normal stress 4 Attachment(s)
    • Replies: 0
    • Views: 2,332
    robert_cibula
    08-24-2018, 03:14 PM Go to last post

  15. A Rookie thats all Ears

    Started by robert_walker, 06-14-2017 07:54 PM
    • Replies: 0
    • Views: 2,441
    robert_walker
    06-14-2017, 07:54 PM Go to last post

  16. Aluminium tube or steel tube for yacht legs ?

    Started by rod, 07-10-2014 11:26 PM
    • Replies: 1
    • Views: 3,298
    Cake of Doom
    07-11-2014, 03:49 AM Go to last post

  17. Question Half Journal Bearing?

    Started by RodNewstrom, 08-09-2021 11:32 AM
    #journalbearing 6 Attachment(s)
    • Replies: 13
    • Views: 3,438
    Cragyon
    11-25-2021, 08:58 AM Go to last post

  18. new thread on bolt

    Started by ronenburstein, 02-06-2021 08:35 AM
    bolts trhead
    • Replies: 5
    • Views: 2,746
    jboggs
    02-15-2021, 11:06 AM Go to last post

  19. Calculating torque of an L shaped lever

    Started by ross_46, 09-30-2018 01:55 AM
    • Replies: 1
    • Views: 2,733
    Kelly_Bramble
    09-30-2018, 06:18 AM Go to last post

  20. Injection Molding Part Design - Reveal - Part Mismatch

    Started by rsimechanical, 10-07-2017 04:45 PM
    cosmetic, injection mold, part design, reveal, seam 2 Attachment(s)
    • Replies: 1
    • Views: 5,612
    Cragyon
    10-13-2017, 10:15 AM Go to last post
Page 24 of 30 FirstFirst ... 14 22 23 24 25 26 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules