Page 27 of 30 FirstFirst ... 17 25 26 27 28 29 ... LastLast
Threads 521 to 540 of 597

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. Determining max bending plane for a shaft with multiple belt loads

    Started by sean_johnson, 11-28-2017 06:54 AM
    belt moment multiple
    • Replies: 1
    • Views: 2,386
    Kelly_Bramble
    11-28-2017, 07:58 AM Go to last post

  2. Forming Solid Round Bar Stock

    Started by madams, 12-19-2018 11:11 AM
    • Replies: 0
    • Views: 2,383
    madams
    12-19-2018, 11:11 AM Go to last post

  3. Need to make cardboard move when a motion sensor detects movement, Renewable energy

    Started by mohdmesi, 03-28-2018 06:59 PM
    • Replies: 0
    • Views: 2,381
    mohdmesi
    03-28-2018, 06:59 PM Go to last post

  4. The Journal Bearing Temperaure Raising During Rainy

    Started by cuongvvu, 06-28-2016 08:18 PM
    • Replies: 1
    • Views: 2,380
    GlennD
    06-28-2016, 10:53 PM Go to last post

  5. prandtle tip correction effect on BEM algorithem

    Started by yose_399, 06-10-2017 04:10 PM
    airfoil, bem, correction factor, iteration, propeller
    • Replies: 0
    • Views: 2,380
    yose_399
    06-10-2017, 04:10 PM Go to last post

  6. Calculating shear in a pin with known torque value

    Started by alexmarks612, 07-05-2022 03:43 PM
    4 Attachment(s)
    • Replies: 2
    • Views: 2,375
    alexmarks612
    07-06-2022, 02:14 PM Go to last post

  7. Yield strength of a gusseted joint

    Started by darren_larkin, 11-08-2016 02:34 PM
    • Replies: 1
    • Views: 2,374
    Hudson
    11-14-2016, 08:02 PM Go to last post

  8. Pneumatic Adjustable Height Massage Table

    Started by doylejason27, 03-30-2018 02:49 PM
    • Replies: 0
    • Views: 2,372
    doylejason27
    03-30-2018, 02:49 PM Go to last post

  9. DIY exccentrical / dual action gearbox to put on a dremel

    Started by matthieu_vankints, 06-16-2017 02:16 PM
    • Replies: 0
    • Views: 2,367
    matthieu_vankints
    06-16-2017, 02:16 PM Go to last post

  10. Damper for Linear Motion

    Started by benjaminguarino, 04-09-2018 06:31 PM
    • Replies: 3
    • Views: 2,366
    Kelly_Bramble
    04-10-2018, 02:30 PM Go to last post

  11. Helpful Math Elective

    Started by chasebonczek, 03-21-2018 09:58 PM
    • Replies: 3
    • Views: 2,365
    dineshmt196
    03-22-2018, 12:16 AM Go to last post

  12. Stress acting on Rack?

    Started by aeroman13, 07-06-2016 03:44 PM
    1 Attachment(s)
    • Replies: 0
    • Views: 2,359
    aeroman13
    07-06-2016, 03:44 PM Go to last post

  13. Video Lectures for Lienhard Heat Transfer Textbook

    Started by drudolf17, 03-03-2020 10:46 PM
    • Replies: 0
    • Views: 2,357
    drudolf17
    03-03-2020, 10:46 PM Go to last post

  14. Confused I need to lift a roof

    Started by herkpilot1, 09-29-2016 07:30 AM
    • Replies: 3
    • Views: 2,354
    Cake of Doom
    10-04-2016, 03:39 AM Go to last post

  15. Conveyor belt to carry vehicles

    Started by dzforumalgerie, 12-13-2018 04:23 AM
    1 Attachment(s)
    • Replies: 1
    • Views: 2,343
    JAlberts
    12-13-2018, 05:07 PM Go to last post

  16. looking to design an automated backlash checker for gearheads

    Started by cliff_turnell, 03-11-2020 04:53 PM
    • Replies: 2
    • Views: 2,342
    cliff_turnell
    03-12-2020, 11:21 AM Go to last post

  17. High Push / Pull Force 12 Volt Actuator

    Started by jasonroliver, 08-20-2018 12:29 PM
    • Replies: 1
    • Views: 2,338
    Kelly_Bramble
    08-20-2018, 12:52 PM Go to last post

  18. Slider Bush and Shaft Selection for Crank Slider

    Started by jaakrob, 12-13-2018 05:38 AM
    #bearing, #bushing, #crank, #materials, #mechanical
    • Replies: 1
    • Views: 2,338
    jboggs
    12-13-2018, 06:32 AM Go to last post

  19. Side entry mixer sizing

    Started by amir_sedieqy, 04-21-2021 03:44 AM
    mixer, side-entry-mixer
    • Replies: 0
    • Views: 2,329
    amir_sedieqy
    04-21-2021, 03:44 AM Go to last post

  20. Question Sensitive accurate material extraction tool for clay like material w/ thin sheathing

    Started by kde5fan, 08-27-2018 12:19 PM
    • Replies: 1
    • Views: 2,329
    JAlberts
    08-30-2018, 04:19 PM Go to last post
Page 27 of 30 FirstFirst ... 17 25 26 27 28 29 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules