F606M-02 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets [Metric]
These test methods establish procedures for conducting tests to determine the mechanical properties of metric externally and internally threaded fasteners, washers, and rivets.
|
F594-02 - Standard Specification for Stainless Steel Nuts
This specification covers the requirements for stainless steel nuts 0.25 to
1.50 in. in nominal diameter inclusive in a number of alloys in common use and
intended for service applications requiring general corrosion resistance.
Seven groups of stainless steel alloys are covered, including ten austenitic,
two ferritic, four martensitic, and one precipitation hardening.
Seven groups of stainless steel alloys are covered, including ten austenitic,
two ferritic, four martensitic, and one precipitation hardening.
| Group |
Alloys |
Condition |
|
|
|
| 1 |
304, 305, 304L, 384, 18-9LW, 302HQ |
(CW) |
cold workedD |
| 2 |
316, 316L |
(CW) |
cold worked |
| 3 |
321, 347 |
(CW) |
cold worked |
| 4 |
430 |
(CW) |
cold worked |
| 5 |
410 |
(H) |
hardened and tempered |
| 6 |
431 |
(H) |
hardened and tempered |
| 7 |
630 |
(AH) |
aged hardened |
|
F593-02e2 - Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
This specification covers the requirements for stainless steel bolts, hex cap
screws, and studs 0.25 to 1.50 in., .inclusive, in nominal diameter in a number
of alloys in common use and intended for service applications requiring general
corrosion resistance.
Seven groups of stainless steel alloys are covered, including twelve austenitic,
two ferritic, four martensitic, and one precipitation hardening.
| Group |
Alloys |
Condition |
| 1 |
304, 305, 384, 304 L, |
(CW) cold worked |
|
18-19LW, 302HQ |
|
| 2 |
316, 316 L |
(CW) cold worked |
| 3 |
321, 347 |
(CW) cold worked |
| 4 |
430 |
(CW) cold worked |
| 5 |
410 |
(H) hardened and tempered |
| 6 |
431 |
(H) hardened and tempered |
| 7 |
630 |
(AH) age hardened |
|
F592-84 - Standard Terminology of Collated and Cohered Fasteners and Their Application Tools
Keywords: collated and cohered fasteners; application tools
|
F568M-04 - Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners
This specification covers chemical and mechanical requirements for nine property classes of carbon and alloy steel externally threaded metric fasteners in nominal thread diameters M1.6 through M100 suited for use in general engineering applications.
|
F547-01 - Standard Terminology of Nails for Use with Wood and Wood-Base Materials
Keyworsd: Nnails; terminology-building applications/materials; wood and wood products; wood and wood products-structural; nails (for wood/wood-base materials)
|
F541-04 - Standard Specification for Alloy Steel Eyebolts
This specification covers forged, quenched and tempered, alloy steel threaded eyebolts with improved toughness properties and intended primarily for low
temperature applications. The eyebolts are chemically and metallurgically constituted to produce a low transition temperature to minimize brittle failure.
Maximum thread size is 2.500 in. (63.50 mm).
The eyebolts are furnished in two types, as follows:
Type1?Straight Shank Eyebolt.
Type 2?Shoulder Eyebolt.
|
F468M-03a - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications.
|
F468-03a - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in. inclusive in diameter manufactured from a number of alloys in common use and intended for general service applications.
|
F467-03a - Standard Specification for Nonferrous Nuts for General Use
This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.
|
|
