B16.26 - Cast Copper Alloy Fittings for Flared Copper Tubes

This standard for Cast Copper Alloy Fitting for Flared Copper Tubes covers: (a) pressure rating; (b) material; (c) size; (d) threading; (e) marking; accordance with the Code of Federal Regulations, Title 49, Part 192, "Minimum Safety Standards for Transportation of Natural and Other Gas by Pipe Line", ASME B31.8, or ANSI Z223.1. The standard shall apply to valves operated in a temperature environment between -20 F and 150 F. This standard sets forth the minimum capabilities, characteristics, and properties which a valve at the time of manufacture must possess, in order to be considered suitable for use in gas piping systems. Details of design and manufacture, other than those stated in this standard, including such design and production tests that will produce a valve that will have the required capabilities to meet this standard, remain the responsibility of the manufacturer. Each test in which damage to the valve could result, i.e.,Tests 3.3,.3.4.1, 3.4.2,3.4.3 and 3.4.4, shall be conducted on new unused samples of the valve.

B16.15 - Cast Bronze Threaded Fittings, Classes 125 and 250

This Standard pertains primarily to cast Class 125 and Class 250 bronze threaded pipe fittings. Certain requirements also pertain to wrought or cast plugs, bushings, couplings, and caps. This Standard covers: (a) pressure-temperature ratings; (b) size and method of designating openings of reducing pipe fittings; (c) marking; (d) minimum requirements for casting quality and materials; (e) dimensions and tolerances in U.S. customary and metric (SI) units; (f) threading.

B89.1.2M - Calibration of Gage Blocks by Contact Comparison Methods, Through 20in. and 500mm

This Standard covers procedures to establish unified practice in calibration laboratories for measuring gage blocks up to 20 in.(500mm) in length (size) by contact comparison methods. It does not cover interferometric comparison methods.

B30.19 - Cableways

Applies to the construction, installation, operation inspection, and maintenance of all load transporting hoisting and lowering cable supported systems operating on and supported from track cable(s). This volume does not apply to skyline systems as used in the logging industry or slackline systems used for excavating.

B16.25 - Buttwelding Ends

This Standard covers the preparation of buttwelding ends of piping components to be joined into a piping system by welding. It includes requirements for welding bevels, for external and internal shaping of heavy-wall components, and for preparation of internal ends (including dimensions and tolerances). Coverage includes preparation for joints with the following. (a) no backing rings; (b) split or noncontinuous backing rings; (c) solid or continuous backing rings; (d) consumable insert rings; (e) gas tungsten are welding (GTAW) of the root pass. Details of preparation for any backing ring must be specified in ordering the component.

B1.9 - Buttress Inch Screw Threads 7/45 Form w/ 0.6 Pitch Basic Height of Thread Engagement

This Standard relates to screw threads of buttress form and provides: (a) A form of 7 degrees/45 degrees buttress thread with 0.6p basic height of thread engagement; (b) A table of preferred diameter-pitch combinations; (c) A formula for calculating pitch diameter tolerances; (d) Tolerances for major and minor diameters; (e) A system of allowances between external and internal threads; (f) Recommended methods of measuring and gaging; (g) Dimensional acceptability of buttress product.

B31.9 - Building Services Piping

This Code Section has rules for the piping in industrial, institutional, commercial and public buildings, and multi-unit residences, which does not require the range of sizes, pressures, and temperatures covered in B31.1. This Code prescribes requirements for the design, materials, fabrication, installation, inspection, examination and testing of piping systems for building services. It includes piping systems in the building or within the property limits.

B107.57 - Bricklayers, Hammers and Prospecting Picks: Safety Requirements

This Standard provides safety requirements for the design, construction, testing, and use of bricklayer's hammers that are intended specifically for use in setting and cutting (splitting) bricks, masonry tile, chipping mortar from bricks, and also of prospecting picks that are intended specifically for use in pulling samples from the ground.

B107.50M - Brick Chisels and Brick Sets: Safety Requirements

This Standard provides safety requirements for the design, construction,testing, and use of brick chisels and brick sets that are intended specifically for use in scoring and cutting brick and masonry block.

International Boiler and Pressure Vessel Code

The International Boiler and Pressure Vessel Code establishes rules of safety governing the design, fabrication, and inspection of boilers and pressure vessels, and nuclear power plant components during construction. The following are the sections contained within the standard as of this publishing - June 2005. BPVC-I 2004- BPVC Section I-Power Boilers BPVC-XI 2004- BPVC Section XI - Rules for Inservice Inspection of Nuclear Power Plant Components BPVC-XII 2004- BPVC Section XII- Rules for Construction and Continued Service of Transport Tanks BPVC-IIA 2004- BPVC Section II-Materials-Part A-Ferrous Material Specifications BPVC-IIB 2004- BPVC Section II-Materials-Part B-Nonferrous Material Specifications BPVC-IIC 2004- BPVC Section II-Materials Part C-Specifications for Welding Rods Electrodes and Filler Metals BPVC-IID 2004- BPVC Section II-Materials-Part D-Properties-(Customary) BPVC-IIIAPP 2004- BPVC Section III-Rules for Construction of Nuclear Power Plant Components-Division 1-APPENDICES BPVC-III NB 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 1-Subsection-NB-Class1 Components BPVC-III NC 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 1-Subsection NC-Class 2 Components BPVC-III ND 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 1-Subsection ND-Class 3 Components BPVC-III NE 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 1-Subsection NE-Class MC Components BPVC-III NF 2004- BPVC Section III-Rules Construction NuclearPower Plant Components-Div 1-Subsection NF-Supports BPVC-III NG 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 1-Subsection NG-Core Support Structures BPVC-III NH 2004- BPVC Section III Rules Construction Nuclear Power Plant Component-Div 1 Subsec NH CL 1 Cmpnts Elev Temp Srvc BPVC-III-NCA 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Subsection NCA-General Requirements Div 1&2 BPVC-III-2 2004- BPVC Section III-Rules Construction Nuclear Power Plant Components-Div 2-Code Concrete Reactor Vessels & Cntnmt BPVC-III-3 2004- BPVC Section III-Division 3 Containments for Transportation and Storage BPVC-IV 2004- BPVC Section IV-Rules for Construction of Heating Boilers BPVC-V 2004- BPVC Section V-Nondestructive Examination BPVC-VI 2004- BPVC Section VI-Recommended Rules forthe Care and Operation of Heating Boilers BPVC-VII 2004- BPVC Section VII-Recommended Guidelinesfor the Care of Power Boilers BPVC-VIII 2004- BPVC Section VIII- Rules for Construction of Pressure Vessels Division 1 BPVC-VIII-2 2004- BPVC Section VIII-Rules for Construction of Pressure Vessels Division 2-Alternative Rules BPVC-VIII-3 2004- BPVC Section VIII-Rules for Construction of Pressure Vessels Division 3-Alternative Rules High Press Vessels BPVC-IX 2004- BPVC Section IX-Welding and Brazing Qualifications BPVC-X 2004- BPVC Section X-Fiber-Reinforced Plastic Pressure Vessels BPVC-CC-N 2004- BPVC Nuclear Code Cases: Nuclear Components BPVC-CC-BPV 2004- BPVC Code Cases: Boilers and Pressure Vessels BPVC-IID 2004- BPVC Section II-Materials-Part D-Properties-(Metric)