Next Page

Pages: [1] 2

Geometric Dimensioning and Tolerancing GD&T Training
Geometric Dimensioning and Tolerancing Training ( GD&T ). Onsite and public seminars ASME Y14.5M - 1994 and ANSI standards.
678-643-1758

More Information:
Geometric Dimensioning and Tolerancing GD&T Training

 

Centrifugal and Positive Displacement Pump Basics Training Online, 3 PDH
The pumps widely used in industry and by commercial buildings and municipalities, can almost all be classified as either centrifugal pumps or positive displacement pumps. The general components and operating characteristics of these two types of pumps are covered in this course, along with discussion of corrective and preventive measures for various pumping problems.

More Information:
Centrifugal and Positive Displacement Pump Basics Training Online, 3 PDH

 

Flow Measurement in Pipes and Ducts Training - 3 PDH
This course is about measurement of the flow rate of a fluid flowing under pressure in a closed conduit. The closed conduit is often circular, but also may be square or rectangular (such as a heating duct) or any other shape. The other major category of flow is open channel flow, which is the flow of a liquid with a free surface open to atmospheric pressure.

More Information:
Flow Measurement in Pipes and Ducts Training - 3 PDH

 

Fundamentals of GD&T Online Training, ASME Y14.5 - 2009, 4.0 PDH
Online certificate training program for the Fundamentals of ASME Y14.5-2009, Geometric Dimensioning and Tolerancing (GD&T).

More Information:
Fundamentals of GD&T Online Training, ASME Y14.5 - 2009, 4.0 PDH

 

Pipe Flow/Friction Factor Calculations with Excel Training - 3 PDH
Several kinds of pipe flow calculations can be made with the Darcy-Weisbach equation and the Moody friction factor. Also, these calculations can be conveniently carried out with an Excel spreadsheet. Many of the calculations require an iterative solution, so they are especially suitable for an Excel spreadsheet solution.

More Information:
Pipe Flow/Friction Factor Calculations with Excel Training - 3 PDH

 

Project Management Basics Online Training - 4PDH
Project management is the discipline of planning, organizing, securing, managing, leading, and controlling resources to achieve specific goals. A project is a temporary endeavor with a defined beginning and end (usually time-constrained, and often constrained by funding or deliverables), undertaken to meet unique goals and objectives, typically to bring about beneficial change or added value.

More Information:
Project Management Basics Online Training - 4PDH

 

Valve Fundamentals Online PDH Training
Valve Fundamentals Online Training, 4 PDH awarded.

More Information:
Valve Fundamentals Online PDH Training

 

Fundamentals of Design for Plastic Injection Molding Training
Fundamentals of Design for Plastic Injection Molding, 45 Days Access, 4 PDH

More Information:
Fundamentals of Design for Plastic Injection Molding Training

 

Lubrication Fundamentals Online PDH Training
This course, the learner will be introduced to the basics of lubrication, friction and wear and how lubrication is used to reduce friction in typical applications. The course materials is derived..

More Information:
Lubrication Fundamentals Online PDH Training

 

Design for Manufacturability DFM Training - Engineers Edge
Design for manufacturing (DFM) training for engineers, designers, drafters, procurement professionals. Concurrent engineering and design, Design for high volume manufacturing, Design for low volume manufacturing, Mechanical dimensions and tolerances, Surface roughness, Cleaning processes, Coatings and Platings, Marking and Identification, Materials and machinability, Milling manufacturing, Turning manufacturing, Sawing and cutoff, Drilling and reaming, Boring, Honing, Trepanning, Gun Drilling and reaming, Ejector drilling, Threading, Hobbing, Surface grinding (center, centerless, in-feed), Electrical discharge machining (EDM), Casting (ferrous and non-ferrous, sand, cold-cure, lost foam, green sand, Investment casting, Die casting, Forging, Extrusion, Electroforming, Rapid prototype, Injection molding plastics, Stamping and forming, sheet metal, Progressive stamping, deep drawing, Spinning (spun) manufacturing, Abrasive water jet, Design for welding, Design for corrosion, Inspection and quality, Engineering drawings and manufacturing, Computer aided design (CAD) and manufacturability, Design for assembly (DFA), Design for maintainability

More Information:
Design for Manufacturability DFM Training - Engineers Edge

 

Next Page

Pages: [1] 2

© Copyright 2000 - 2018, by Engineers Edge, LLC All rights reserved.
Disclaimer

List Your Company HERE!! Add SEO Directory Listing | Advertising Information